Need help with Serv-U 5.2 & SSL/TLS
Hi,
I have FlashFXP v3.0 B1015 and Serv-U v5.2.
I can't make FlashFXP work in SSL mode or TLS mode. In implict SSL mode, with the Server set for secure only on port 990, I can connect and negotiate the secure connection, but I cannot get a directory listing. No matter what connection settings I try in FlashFXP. My testing was done on my internal LAN. So my firewall is not a factor. Even if it was, which I thought might be the case at first, there are no entries in my firewall log. Can't be the firewall though or my FlashFXP connection settings, cause unsecure works fine, and auth ssl/tsl doesn't. Without changing anything else.
I get this same problem using either Auth SSL or TLS with the server set to accept both secure and non secure on port 21.
Here is what I get:
WinSock 2.0 -- OpenSSL 0.9.7d 17 Mar 2004
[R] Connecting to <S1> -> IP=10.0.0.1 PORT=21
[R] Connected to <S1>
[R] 220 Serv-U v5.2.0.0 FTP Server ready.
[R] AUTH SSL
[R] 234 AUTH command OK. Initializing SSL connection.
[R] Connected. Negotiating SSL session..
[R] SSL negotiation successful...
[R] SSL encrypted session using cipher AES128-SHA (128 bits)
[R] PBSZ 0
[R] 200 PBSZ command OK. Protection buffer size set to 0.
[R] USER ******
[R] 331 User name okay, need password.
[R] PASS (hidden)
[R] 230 User logged in, proceed.
[R] SYST
[R] 215 UNIX Type: L8
[R] FEAT
[R] 211-Extension supported
[R] AUTH TLS
[R] SSCN
[R] PBSZ
[R] PROT
[R] CCC
[R] CLNT
[R] MDTM
[R] MDTM YYYYMMDDHHMMSS[+-TZ];filename
[R] SIZE
[R] SITE PSWD;EXEC;SET;INDEX;ZONE;CHMOD;MSG
[R] REST STREAM
[R] XCRC filename;start;end
[R] MODE Z
[R] 211 End
[R] CLNT FlashFXP 3.0.1015
[R] 200 Noted.
[R] PWD
[R] 257 "/f:" is current directory.
[R] TYPE A
[R] 200 Type set to A.
[R] PROT P
[R] 200 PROT command OK. Using private data connection.
[R] PASV
[R] 227 Entering Passive Mode (10,0,0,1,39,21)
[R] Opening data connection IP: 10.0.0.1 PORT: 10005
[R] LIST -al
[R] Connected. Negotiating SSL session..
[R] 150 Opening ASCII mode data connection for /bin/ls.
(It sticks right there until the connection times out.)
In Auth SSL/TLS mode, using only secure file transfer selection, It clips right on through, but I still get no directory listing. Again, in no ssl mode, I get a full directory listing.
Here's what I get in this mode:
WinSock 2.0 -- OpenSSL 0.9.7d 17 Mar 2004
[R] Connecting to <S1> -> IP=10.0.0.1 PORT=21
[R] Connected to <S1>
[R] 220 Serv-U v5.2.0.0 FTP Server ready.
[R] AUTH SSL
[R] 234 AUTH command OK. Initializing SSL connection.
[R] Connected. Negotiating SSL session..
[R] SSL negotiation successful...
[R] SSL encrypted session using cipher AES128-SHA (128 bits)
[R] PBSZ 0
[R] 200 PBSZ command OK. Protection buffer size set to 0.
[R] USER ******
[R] 331 User name okay, need password.
[R] PASS (hidden)
[R] 230 User logged in, proceed.
[R] SYST
[R] 215 UNIX Type: L8
[R] FEAT
[R] 211-Extension supported
[R] AUTH TLS
[R] SSCN
[R] PBSZ
[R] PROT
[R] CCC
[R] CLNT
[R] MDTM
[R] MDTM YYYYMMDDHHMMSS[+-TZ];filename
[R] SIZE
[R] SITE PSWD;EXEC;SET;INDEX;ZONE;CHMOD;MSG
[R] REST STREAM
[R] XCRC filename;start;end
[R] MODE Z
[R] 211 End
[R] CLNT FlashFXP 3.0.1015
[R] 200 Noted.
[R] PWD
[R] 257 "/f:" is current directory.
[R] TYPE A
[R] 200 Type set to A.
[R] PROT C
[R] 200 PROT command OK. Using clear data connection.
[R] PASV
[R] 227 Entering Passive Mode (10,0,0,1,39,17)
[R] Opening data connection IP: 10.0.0.1 PORT: 10001
[R] LIST -al
[R] 150 Opening ASCII mode data connection for /bin/ls.
[R] 226 Transfer complete.
[R] List Complete: 0 bytes in 0.20 seconds (0.0 KB/s)
Thanks for any help,
Red
|
Linear Mode
