Testing with 3805-r3
1. Repeating Example 3 from previous posts... everything within the initial CMD seems to be performed in the correct order now, however tasks from sub command CMD2 still do not function in the expected order. Sub command raws and echos (not sure if other commands are affected or not) are still misplaced.
Code:
#CMD
/echo -- Enqueue A
/enqueue A
A
{
/cd %p%f
[CMD2]
}
/uncd
#CMD2
/echo -- Enqueue B
/enqueue B
B
#LOG
[18:15:53] [L] [CMD] -- Enqueue A
#A is correctly enqueued
[18:15:53] [L] A
[18:15:54] [L] 500 'A': Command not understood.
[18:15:54] [L] [CMD] /cd /tools/bin/TESTING
[18:15:54] [L] CWD /tools/bin/TESTING
[18:15:54] [L] 250 CWD command successful.
[18:15:54] [L] PWD
[18:15:54] [L] 257 "/tools/bin/TESTING" is current directory.
[18:15:54] [L] STAT -l
[18:15:55] [L] List Complete: 549 bytes in 0.86 seconds (0.5 KB/s)
[18:15:55] [L] [CMD] CMD2
#B is correctly enqueued
[18:15:55] [L] [CMD] /cd /tools/bin/TESTING2
[18:15:55] [L] CWD /tools/bin/TESTING2
[18:15:56] [L] 250 CWD command successful.
[18:15:56] [L] PWD
[18:15:56] [L] 257 "/tools/bin/TESTING2" is current directory.
[18:15:56] [L] STAT -l
[18:15:57] [L] List Complete: 201 bytes in 0.86 seconds (0.2 KB/s)
[18:15:57] [L] [CMD] CMD2
#B is correctly enqueued again
[18:15:57] [L] [CMD] /uncd
[18:15:57] [L] CWD /tools/bin
[18:15:57] [L] 250 CWD command successful.
[18:15:57] [L] PWD
[18:15:58] [L] 257 "/tools/bin" is current directory.
[18:15:58] [L] STAT -l
[18:15:58] [L] List Complete: 7,618 bytes in 0.87 seconds (7.4 KB/s)
#Misplaced echos and raw commands
[18:15:58] [L] [CMD] -- Enqueue B
[18:15:58] [L] B
[18:15:59] [L] 500 'B': Command not understood.
[18:15:59] [L] [CMD] -- Enqueue B
[18:15:59] [L] B
[18:15:59] [L] 500 'B': Command not understood.
Expected behavior...
Code:
/echo -- Enqueue A
/enqueue A
A
/cd /tools/bin/TESTING
/echo -- Enqueue B
/enqueue B
B
/cd /tools/bin/TESTING2
/echo -- Enqueue B
/enqueue B
B
/uncd
Previous build evaluated to...
Code:
/echo -- Enqueue A
/enqueue A
/cd /tools/bin/TESTING
/enqueue B
/cd /tools/bin/TESTING2
/enqueue B
/uncd
A
/echo -- Enqueue B
B
/echo -- Enqueue B
B
This build evaluated to...
Code:
/echo -- Enqueue A
/enqueue A
A
/cd /tools/bin/TESTING
/enqueue B
/cd /tools/bin/TESTING2
/enqueue B
/uncd
/echo -- Enqueue B
B
/echo -- Enqueue B
B
2. /delay does not function, seems to ignore the numeric parameter completely. It always starts a countdown of ~4294968 seconds (almost 50 days).
3. While doing a few tests I have noticed that command progress status bar updates are bugged somehow. In the above 'Example 3' the X value in X of Y is probably mostly incorrect due to the ordering issue with CMD2 (so it just appears odd). However the limited testing i was able to do shows that initial count for Y is also wrong in some cases. Take the following example... Y is evaluated to 5, /cd is shown as 1 of 5 and /uncd is shown as 4 of 5. I believe X is correct but the initial 5 value for Y is not. Perhaps counting the close group }?
Code:
{
/cd %p%f
/select -d rx: (?-i).*\.min
/queue selected
}
/uncd
4. When an enqueued command (eg /ren) encounters a problem (eg 550 on RNTO) is it intentional that the enqueued command queue entry still be removed rather than marked as failed?
I was unable to find any old commands that did not continue to perform as expected with this build. This includes the command i wrote that started all this discussion which continues to function correctly (since the sub command only contains one /enqueue line). Since sub command support is relatively new I think it is safe to assume very minimal if any custom commands created by people are likely to malfunction as a result of fixes here - also since the tasks most affected are those that people are unlikely to mistakenly put in the wrong place / rely on being in the wrong place.